Average Speed、Max Speed 、AVG

Unit: MPH, KM/H

Speed has 4 ways to come true，depending on the specific way，partial

way could compose.

1. Hall signal attaching electric motor

2. Controller send Hall signal of motor to meter

3. slow speed Hall signal as the type run a circle.

4. Controller send signal of slow Hall signal as type run a circle to meter.

(single Hall cycle, Unit： 1MS )

The meter could calculate true speed according to the data of wheel

diameter and the signal’s data (electric motor’s Hall need to set up the

 magnet steel’s quantities)

4.8 Set

P01：Backlight lamp brightness, level 1 is the most dark, level 3 is

 the brightest;

P02：Unit mileage, 0: KM;1: the MILE;

P03：Level of voltage: 24 v, 36 v, 48 v, 36 v (by default);

P04：Sleep time: 0, means don't sleep;Other Numbers means for

 the sleep time,

  range: 1-60;Units of minutes;

P05：Assistance gears:0, 3Mode：1lever  2V、2lever  3V、3lever  4V;

                     1, 5Mode：1lever  2V、2lever  2.5V、3lever  3V、

4lever  3.5V、5lever  4V;

P06：Wheel diameter: unit, inch;Accuracy: 0.1;

P07：Speed measuring magnetic steel number: range: 1-100;

P08：Speed: the range 0 to 50 km/h;The default 50, 50 said not

the speed limit;

Note：when the speed is greater than the set speed, shut off the

 PWM output;When speed down to less than the set speed,

automatically open the PWM output, driving speed to the

current + 1 km/h;
Numerical based on km as a benchmark here, after the unit set

from miles to miles, display the speed of numerical value is

automatically converted to the correct miles, but miles under

the interface of the menu in the values of speed limit set by

the data conversion, MPH speed limit values are not consistent

with the actual display,

P09：Zero start, non-zero start setting, 0:0 start;1: the non-zero start;

P10：Driving mode setting 0: power drive (decided how much

output power by power gear, at this time to turn the invalid).

1: electric (by going to drive, steering gear is invalid at this time).
2: power drive and electrical drive coexist (electric zero start state

 is invalid).

P11：Power sensitivity setting range: 1-24;

P12：Assistance start the intensity setting range: 0-5;

P13：Power magnetic steel plate type 5 Sherwin grain of magnetic

steel three types;

P14：Controller for the current limit value to set,12A(by default)

range: 1 - 20 A;

P15  Not implemented now.

P16  Reset ODO. Long press  for 5s, ODO could be reset.

Specific buttons position as bellow:

Button’s Design Introduction

Button operation includes short-time press, long-time press and

combination buttons long-time press.

 

Short-time press used in quickly/frequently operation, such as:

Button’s Design Introduction

Button operation includes short-time press, long-time press and

combination buttons long-time press.

 

Short-time press used in quickly/frequently operation, such as:

5.1    During riding, press shortly to change

assistance/speed gear.

5.2  During riding, press shortly to switch the multifunctional

area to display data.

Press single button for long time is mainly to switch the mode/button status.

Press combination button (for long time) is mainly used for parameter

setting, which could reduce maloperation due to complicated operation.

(No combination buttons with short-time press, as they are too difficult

to operate due to they are easy to be triggered by mistake).

Explain of Specific Operation：

1.      Shift to assistant/electric gear,

Suppose current condition is assistance mode,

1)Shortly press , assistance + 1

2)Shortly press ,assistance - 1

 

2.      shift speed display

Long press  to shift the way of speed display

3.      Long press ,delete Trip

4.      set/ release the condition of 6km/h cruise、real time cruise,on/off light

When the e-bike is stops,extended press ,you can get into

the 6KM/h cruise mode. When the e-bike is running, extended

press ,you can get into the real time cruise mode. If just

now you are in cruise mode, the mode will be released.

Shortly press  to turn on/off light.

5.      Turn on/off LCD screen

If current display screen is working, extended press ,the

screen will be off, otherwise, the screen will be on.

6.      Shift to multifunctional display version,

Shortly press , you can shift the value on multifunctional

display version.

7.      parameter setting

Press + and hold, get into the version of parameter

setting, then you can set up parameters bellow,wheel diameter

(unit: inch), magnet steel number,LCD brightness, under-voltage

point etc.( See Settings: P01 - P14)

Under the set interface,you could shortly press  or  

to add or subtract the value, after modified the parameters ,it will be

shine,after you choose the assumed value,

1) Press  shortly to save current value,parameters shine

 will be stop .

2) Press +,save setting, if didn’t press, it will be

 automatically save and exit after 10 seconds to modify parameters

 

Note：according to upgrading of our products, there may be some

differences between product introduction and products you received.

The differences would not influent your daily usage.